Welch-allyn LC101 CO2 Module - User Manual Manual de usuario Pagina 69
- Pagina / 98
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LC101 CO
2
Module OEM Implementation Manual
Appendix C - Error Messages & Recovery
Welch Allyn OEM Technologies Confidential Page 69
24, Calibration Ready for Next Step
The calibration sequence has been initiated, and the Module requires data commands from the
host to proceed to the next calibration step.
25, Calibration in Progress
The Module is carrying out the calibration process.
26, Calibration OK
The Module has successfully performed a calibration, and the new constants have been stored in
the EEPROM. After successful User Calibration, the Last Calibration Date is also updated to
reflect the new information.
Soft Faults
Soft faults are conditions which halt Module operation, including transmission of CO
2
waveform
and breath data packets, until the condition is cleared. The Module can accept commands while
in the soft fault state.
Calibration Faults
Calibration faults abort calibrations. The Module requires a new calibration command to reinitiate
the calibration sequence after the error is cleared. Calibration fault messages include 28 through
2A. To clear a calibration fault, send a new host command. If the Module does not accept the
command, a software reset may be required.
Calibration faults are listed in the following table.
28, Unable to Perform Calibration, Parameters Missing
The Module timed out while waiting for a data command from the host during the calibration
sequence. The calibration sequence must be completed within 30 minutes of initiation.
Status
Message Code
(hex)
Definition Possible Causes
28 unable to perform
calibration, parameters
missing
• calibration sequence must be completed within 30
minutes
29 unable to perform
calibration, data error
• acquired CO
2
data is invalid for calibration
sequence; error also provided if calibration is
aborted due to another error
2A bad calibration crc • error in system EEPROM
- LC101 CO 1
- Functional Description 7
- Terminology 8
- Measuring Principle 8
- Measurement Calculation 9
- Measurement Compensation 10
- Hardware Components 11
- Sidestream Components 13
- LC101 Module Interface 15
- Watertrap Switch Connection 16
- Watertrap Receiver 16
- Watertrap Receiver Switch 17
- Exhaust Tubing 17
- LC101 Calibration 19
- Zero Calibration Procedure 20
- Section 3 - LC101 Calibration 21
- Troubleshooting 24
- Host/Module Communications 25
- Packet Structure 26
- Host Commands 27
- Simple Commands 28
- Configuration Commands 29
- C-Cap EEPROM Memory Map 32
- Status Responses 34
- Mode Command Responses 35
- Simple Command Responses 36
- Example: 38
- Calibration Command Responses 40
- Software Protocol 41
- Status Message Code Table 44
- Code (hex) Suggested Message 44
- Fault OFF OFF NO 46
- Standby OFF OFF NO 46
- Measurement ON ON YES 46
- Autorun ON ON YES 46
- Pneumatic Operation 47
- Pneumatic Events 48
- Total Exhaust Occlusion 49
- Partial Exhaust Occlusion 49
- Barometric Out Of Range 49
- Unexpected Reverse Flow 49
- Internal Disconnects 50
- Pump Failure 51
- Regulatory 53
- Electromagnetic Interference 54
- Compliance Testing Summary 54
- ISO 9918 and EN 864 54
- Software Procedures 55
- Percent CO 56
- Calculation 56
- Seq Host Module Description 58
- CCITT/CRC Code Calculation 60
- Software Upgrade 61
- EEPROM Memory Map 63
- Error Messages & Recovery 65
- Advisories 66
- Too Large 67
- Calibration Advisories 68
- Soft Faults 69
- Sensor Faults 70
- System Faults 72
- Welch Allyn OEM Technologies 75
- Part Numbers and Accessories 75
- Technologies 76
- Specifications 77
- Appendix E - Specifications 79
- (Ref. 000.10100.UOO Rev. 0) 79
- Developer’s Kit 83
- Software Installation 84
- Initial Setup 84
- Appendix F - CO 85
- Menu Options Description 86
- 50 mmHg 6% 88
- 75 mmHg 10% 88
- 100 mmHg 14% 88
- Glossary 91
Relacionado con productos y manuales para Equipo Welch-allyn LC101 CO2 Module - User Manual
Equipo Welch-allyn LumiView Portable Binocular Microscope - User Manu Manual de usuario
(84 paginas)
(84 paginas)
Equipo Welch-allyn SureSight Vision Screener Autorefractor - User Man Manual de usuario
(32 paginas)
(32 paginas)
(192 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales