Welch-allyn Image Capture System - User Manual Manual de usuario

Image Capture SystemDirections for Use

63. To connect the DV Converter to the Video Colposcope, plug one end of the provided S-Video Cable into the Video In on the DV Converter and the oppo

74. To connect the Video Colposcope to the computer, plug one end of the provided RS-232 Cable into the top connection on the Video Colposcope and the

8system requirements, the software will not work reliably and you will experience problems such as no video image. 1. Load the Welch Allyn Image Captu

9DirectX 8.1The Image Capture System software requires that version 8.1 or later of DirectX is installed on the computer. Windows 2000 shipped with Di

10Setting Up the Welch Allyn Image Capture SystemSystem AdministratorWelch Allyn recommends that the System Administrator for the Welch Allyn Image Ca

114. The Hardware tab allows the System Administrator to select the video device, video inputs (the Image Capture System does not use video inputs), a

122. Click on the Settings drop-down menu. Click on the Application selection in the drop-down menu. This brings you to the Application Settings scree

13b. Captured Image File Format. This setting allows the user to choose the saved image file format. Click the drop down arrow to choose a BMP, JPG, o

14c. Display Destructive Timestamp on Captured Image. The Timestamp setting permanently marks the current date and time on the image the moment the im

15Entering Patient SessionsThe user can load information for a new patient or a new session from the same opening screen. The system always displays t

Windows® is a registered trademark of Microsoft Corporation.Welch Allyn® is a registered trademark of Welch Allyn, Inc.© Copyright Welch Allyn, Inc. 2

16Adding a New PatientTo add a new patient in the Welch Allyn Image Capture System:1. Login to the Welch Allyn Image Capture System. Your password bri

17Using the Welch Allyn Image Capture SystemWhen entering a New Session, the Welch Allyn Image Capture System always begins in Image Capture Mode. Use

18Using the Video Colposcope ButtonsThe Welch Allyn Video Colposcope has three buttons located just above the handle that allows it to send commands t

19Reviewing Sessions and ImagesCaptured images are available for the user to delete, export, or print. Pressing the Delete button will remove the sele

202. Answer Yes to verify that you want to remove the image from the session folder. The computer display is cleared of the deleted image and the acti

21Copying SessionsThis feature allows the user to copy or back up all or selected sessions.1. Login to the Welch Allyn Image Capture System. Your pass

22MaintenanceCheck all connection cables once a month for kinks, fraying, or other damage. Replace as necessary.Consult the accessory specific manual

23System Administrator password doesn’t work.Password is case sensitive.Check the current status of the Caps Lock Key and re-type the password.Passwor

24Colposcope buttons do not work, but the Image Capture Software buttons do work. Defective RS-232 cable.Check your RS-232 cable for fraying, breakage

25The Image Capture System is not working at all.You need to install .NET Framework 1.1The Image Capture System application requires version 1.1 of th

Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1I

26SpecificationsDV Converter: See enclosed manual.Colposcope: See the Video Colposcope manual.PCI or PCMCIA Card: See enclosed manual.Cable Lengths:S-

27Emissions and Immunity InformationRadiated and Conducted Emissions were tested on the Elgar power source. It complies with the EN55022 Class B limit

28ESD, EFT, and Surge testing were performed on the Schaffner Best EMC multi tester. The power supplied using the Elgar power source at 120VAC. Voltag

29.Conducted RFI and Radiated RFI testing was performed on the EUT. Monitoring the output for drops in voltage; none were detected.Guidance and Manufa

30Software License AgreementThe software provided with the Image Capture System (ICS) consists of software written by Welch Allyn, Inc. (the ICS Softw

31device to the dealer from which you purchased it within the time permitted for returns under your purchase agreement. Welch Allyn may terminate th

32Warranty and ServiceWarrantyWelch Allyn warrants the Welch Allyn Image Capture System, when new, to be free of defects in material and workmanship a

4341 State Street RoadSkaneateles Falls, NY 13153Phone: (315) 685-4560 or (800) 535-6663Fax: (315) 685-3361Material Number: 700144 Rev E

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Approvals . . . . .

1IntroductionThis manual describes the setup, installation, and use of the Image Capture System for Desktop Computers, REF 88801 and Image Capture Sys

2Warnings and CautionsWARNING: This device is not suitable for use in the presence of a flammable anesthetic mixture with air or oxygen or nitrous oxi

3"Welch Allyn recommande vivement que l’Image Capture System soit installé par un représentant formé de Welch Allyn."Si vous décidez d'

4Setting up the ComputerIf you choose to have a third party setup the computer and install the Image Capture System software verify that the system wo

5Connecting the Welch Allyn Image Capture System1. Unplug the Video Colposcope and the Video Colposcope Monitor from the electrical outlet before maki